You are here: Home > WHAT'S NEW



WHAT'S NEW AT INCREMENTAL TOOLS?

MICROJIG FITFINDER 1/2 MACHINE SETUP GAUGE


The FitFinder 1/2 Gauge automatically finds half the thickness of your workpiece using simple geometry, no math or measuring required! Simplifies setting up resawing jobs, cutting half lap joints and more.



MICROJIG MATCHFIT DOVETAIL TRACK CLAMP AP


The Anti-Pivot Coil Spring keeps the clamp arm from dropping when unclamping – no need to constantly reset your clamp height during repetitive jobs, and the included X-PAD™ simultaneously applies vertical hold-down and lateral in-line pressure as the clamp tightens, letting you do more clamping with fewer clamps.



MICROJIG BLADEMATCH ARBOR SHIMS


Easily compensate for variations among your blades' widths! These high-quality stainless steel shims let you offset your blade's cut line to perfectly match the saw's riving knife, plus there's no need to re-zero the rip fence's scale with each blade change. Great for tweaking the kerf width of 2-piece box joint blade sets, too.



MICROJIG DOVETAIL CLAMP PRO


Get all the good stuff in one kit! It's the perfect introduction to the MicroJig MatchFit System's versatility.




MICROJIG MATCHFIT X-PAD™ (4-PACK)


The X-Pad™ is an upgrade for existing MatchFit Dovetail Clamps that allows you to clamp in two directions at once, simultaneously applying hold-down and in-line pressure as the clamp tightens. X-Pads slide onto the round cap of any MatchFit Dovetail Clamp.


RIDGE CARBIDE RS1000 10x60T SAW BLADE


The RS1000 the ideal miter saw upgrade for crosscutting jobs in solid lumber and for dealing with fragile veneered plywood. This blade is super stiff and razor-sharp…yes, there really is a difference between premium blades like Ridge Carbide & Forrest over the blades sold in big-box stores. 10” x 60T alternate top bevel + raker grind, 1/8” (0.125”) kerf, 5/8” arbor.


RIDGE CARBIDE TS2000 10x40T SAW BLADE


Don't like changing blades? Ridge Carbide's TS2000 offers exceptional performance across a wide range of jobs - super smooth rips and crosscuts in solid lumber up to 2" thick, splinter-free cuts in plywood, and even basic joinery. Yes, there really is a difference between premium blades like Ridge Carbide & Forrest over the blades sold in big-box stores. 10" x 40T alternate top bevel grind w/ 8 flat raker teeth, 1/8" full kerf or 3/32" thin kerf, 5/8" arbor.


RIDGE CARBIDE 8" STACK DADO


Ridge Carbide's tight tolerances, extreme sharpness, and -5° hook angle will provide tearout-free grooves in both solid lumber and on fragile surfaces like veneered plywood or melamine. Adjustable from 1/4" to just over 7/8", including widths like 15/32" & 23/32" for undersized plywood, and includes mental shims for fine-tuning. 8" diameter, 5/8" arbor.


RIDGE CARBIDE TRIPLE PLAY BOX JOINT BLADE SET


The Triple Play is another great value in Ridge Carbide' long line of top-quality cutters - tight tolerances, extreme sharpness, and a moderate price. It's adjustable like a stack dado but cuts like dedicated flat-topped box joint blades. Kerf adjustable from 3/16" - 7/16" and micro-adjustable with included metal shims. Note: Designed for box joints and long-grain grooves only - use a conventional dado set for cross-grain cuts.


MILWUKEE 5625-20 HEAVY DUTY 3.5HP ROUTER


Milwaukee's 3.5hp production router is ideally paired with an INCRA Router Lift, it works great with conventional router mounting plates, and it's even remarkably easy to use freehand. Includes 1/2" precision collet, forged wrenches, and an above-table height adjuster. Imported. 5yr limited warranty.


MILWUKEE 5616-20 BODYGRIP 2.25HP ROUTER


Milwaukee's 2.25hp fixed-base 5616 is the right answer for many situations that call for a midsize router - it's equally at home installed in the INCRA MastRLift-II router lift, mounted to an INCRA MagnaLOCK router plate, or used for freehand routing. Includes 1/2" & 1/4" precision collets, forged wrenches, and an above-table height adjuster. Imported. 5yr limited warranty.


MILWUKEE 1/4" ROUTER COLLET ASSEMBLY


Don't forget this extra collet! The 3.5hp Milwaukee 5625-20 routers include only the 1/2" collet, and many smaller router bits are only available with 1/4" shanks. Milwaukee collets are more accurate than most, so we consider using the 1/4" collet a better solution than using the 1/2" collet with a sleeve-type reducer. Compatible with the Milwaukee 5625-20, 5626, 5616-(xx), and 5615-(xx) routers.


INCRA PRECISION TINY T-RULE 75MM


Our smallest T-Rule could be the handiest for small jobs! Measuring only 75mm x 115mm, it offers INCRA's patented marking holes and slots that accurately guide your 0.5mm mechanical pencil to spacings of 1mm, 0.5mm, and 0.25mm on a scale reading 0 - 75mm.


INCRA PRECISION METRIC RULE SET - 150MM


This 3-piece set of INCRA 150mm Precision Rules covers the basics for your small-scale layout work. Set includes a Precision T-Rule for marking points and drawing lines parallel to the edge of a board, Precision Marking Rule for working out of inside corners, Precision Bend Rule for transferring layout marks around the edges of boards, and a FREE 0.5 mm mechanical pencil.

INCRA PRECISION METRIC RULE SET - 300MM


This 3-piece set of INCRA 300mm Precision Rules is the all-around champion of general woodworking layout. Set includes a Precision T-Rule for marking points and drawing lines parallel to the edge of a board, Precision Marking Rule for working out of inside corners, Precision Bend Rule for transferring layout marks around the edges of boards, and a FREE 0.5 mm mechanical pencil.

MICRO JIG MATCHFIT DOVETAIL BIT


Micro Jig's unique 1/2", 14? dovetail bit is designed specifically for routing grooves for the Micro Jig MATCHFIT Dovetail Clamps, leaving a cleaner groove than conventional dovetail bits. Note: This router bit won't work for dovetail joinery with INCRA fence systems or dovetail jigs.

Carbide tipped, 1/2" shank.


MICRO JIG MAGNETIC DUST COVER FOR CABINET SAWS


Micro Jig's Magnetic Dust Cover closes the bevel slot on steel left-tilt cabinet saws, focusing dust collector airflow where it?s most effective. Trim to fit with scissors, can be reversed for right-tilt cabinet saws or for cutting bevels.

MICRO JIG GRR-RIPPER REPLACEMENT LEG SET


Micro Jig GRR-Ripper Replacement Leg Set Are the legs on your GRR-Ripper push blocks showing some wear & tear? This replacement leg set includes the standard 1/4" & 1/2" outer legs and the adjustable center leg, and they install quickly on all GRR-Ripper models using the original hardware. Made in USA.

WOODPECKERS MITER SLOT NUT 4PK


Easily attach feather boards and fixtures to the 15/16? T-slot in your machines? 3/4?x 3/8? miter slots with these unique steel nuts. Includes 4 sets of nuts, knobs, and hardware. Miter channel not included. Made in USA.




WOODPECKERS MULTI-KNOB 4PK 1/4", 5/16", & 3/8"


These unique knobs can be assembled either as female thru knobs by adding your own hex nuts or as male knobs of any thread length by using standard hex bolts. Super tough plastic construction, sized to accept hex nuts & bolts in 1/4?, 5/16?, or 3/8? thread sizes. Sold in packs of 4, fasteners not included. Made in USA.

WOODPECKERS MULTI-KNOB MINI-T (10 PK)


These unique knobs can be assembled either as female thru knobs by adding your own hex nuts or as male knobs of any thread length by using standard hex bolts. Super tough plastic construction, sized to accept 1/4?-20 hex nuts & bolts. Sold in packs of 10, fasteners not included. Made in USA.

WOODPECKERS BLADESAVERS


Protect your investment with Woodpeckers new BladeSavers! These tough ABS plastic guards prevent damage to brittle carbide tips and have an integrated hook for easy storage. Saw blades sold separately.
Made in USA.




INCRA 0.5MM MECHANICAL PENCIL 10-PACK


INCRA 0.5mm pencils work with INCRA Rules to perfectly mark your work without parallax or angle slip, and they're ideal for all your layout tools. Preloaded with several extra leads and easily refillable after that.


INCRA-LOGO BASEBALL CAPS


Stand out from the crowd with an embroidered INCRA hat. 100% Cotton, comfy Velcro adjustment strap, low profile design!


MICRO JIG MATCHFIT DADO STOP PRO


Micro Jig's Dado Stop Pro eliminates endless fine tuning when setting up for dados, lap joints, and inlay work. Automatically adjusts for both the blade kerf and board thickness up to 13/16". Includes (1) each MatchFit Dado Stop, MatchFit Dovetail Clamp, & MatchFit Setup Gauge.


MICRO JIG DADO STOP STEUP GAUGE


When you need accurate dados, the new Setup Gauge accessory for Micro Jig's MatchFit Dado Stop makes that tool's setup even faster. The gauge records you blade kerf with a one-time cut, and then transfers that to your Dado Stop each time you set it to match a different material thickness. Order a couple to record your different kerf blades!




INCRA RT COMBO-3 "The Works"


The new Router Table Combo 3 "The Works" is an extension of RT Combo 3, adding the most popular accessories at a substantial discount: Exceptional dust collection from the INCRA CleanSweep System, wheels, a remote switch, plus the accuracy & convenience of an INCRA Router Lift.









INCRA METRIC POSITIONER SYSTEMS & ACCESSORIES


If you've been putting off the purchase of one of woodworking's most exciting tools because it was not available in a Metric model, your wait is over. INCRA's amazing LS Positioner Fence Systems are now available in FULL METRIC VERSIONS.

INCRA Metric LS17 Positioner Only
INCRA Metric LS32 Positioner Only
INCRA Metric LS Standard System - 430mm Range
INCRA Metric LS Super System - 430mm Range
INCRA Metric TS-LS Table Saw Fence System - 810mm
INCRA Metric TS-LS Table Saw Fence System - 1320mm
INCRA Metric TS-LS Joinery System - 810mm Range
INCRA Metric TS-LS Joinery System - 1320mm Range
INCRA Metric Router Fence & Table Combo #1
INCRA Metric Router Fence & Table Combo #2
INCRA Metric Router Fence & Table Combo #3
INCRA Metric Router Fence & Table Combo #4
INCRA Metric Table Saw Router Table Combo #1
INCRA Metric Table Saw Router Table Combo #2
INCRA Metric Table Saw Router Table Combo #3
INCRA Metric Table Saw Router Table Combo #4
Master Reference Guide & Template Library - Metric Version
INCRA Shop Stop
INCRA Stand Alone 37" Wonder Fence
Wonder Fence Upgrade for LS or Ultra Positioner System
Wonder Fence Joinery Package
INCRA Pro-II Joinery Fence
INCRA Router Bit Sets - Metric Joinery Set
LS Positioner Metric Conversion Kits
Metric Rack Packs