|
|
|
|
|
|
|
|
INCREMENTAL TOOLS SPECIALS:
|
|
|
|
|
|
|
|
SAVE 14% ON JESSEM FEATHER BOARD DOUBLE PACKS
Now only $48.95
 |
JessEm's unique two-piece design of these feather boards allows super-fast setups: The feathers remain parallel to the lumber when adjusting the pressure and shortened first feather acts as a setting jig for no-fuss set up. They can be stacked double for wide boards, they attach quickly to fences T-slots with 1/4" hardware, and they even include fittings for installation in the standard 3/4" miter slots.
|
|
|
|
SAVE $15 ON JESSEM CLEAR CUT ROUTER TABLE STOCK GUIDES
Now only $109.95
|
One pair of these burly aluminum stock guides attached to your fence can replace up to 4 conventional feather boards! The wheels are angled 5 degrees to automatically push lumber against your fence while holding it down, and the wheels' one-way bearings prevent boards from kicking back. They attach quickly to 1/4" router fence T-slots and setup fast with single-knob control. Made in Canada.
|
|
|
SAVE $40 ON JESSEM TS STOCK GUIDES
Starting at $274.95
|
JessEm’s new TS Stock Guides feature the fast setup, kickback resistance, and the consistent hold down & hold-in pressure needed to get the cleanest cuts possible on your table saw. The one-way rollers are set at a 5 degree angle to the fence - as you feed forward, the guides automatically steer the lumber toward the fence and keep it there while reducing the chance of kickback by limiting the lumber's ability to travel back toward the operator. The stock guides can be installed on most flat-topped rip fences, and they’re a no-drill installation on Incra table saw fences when combined with the optional riser kit. Made in Canada.
|
|
|
|
|
|
|
SAVE $20 ON RIDGE CARBIDE TS2000 10” x 60T CROSSCUT BLADES
Now only $129.95
The new 60-tooth version of the tried-and-true TS2000 is the ideal tool for extended crosscutting jobs in solid lumber and for ripping & crosscutting chip-prone sheet goods. Are you using an INCRA miter gauge or sled to produce parts for frames or segmented turnings? Start here! The shallow +5° rake makes it gentle on veneered plywood, too, plus it’s razor-sharp with the carbide tips’ faces and tops polished to 1200 grit. The 1/8” kerf and 0.087”-thick body make the TS2000 stiffer than thin kerf blades to improve your saw’s accuracy. 10” x 60T alternate top bevel grind, 5/8” arbor. Made in USA.
|
|
|
|
|
SAVE 25% ON INCRA BUILD-IT BRACKETS
Now only $8.95
Great for attaching fences and other jig accessories at right angles to your Build-It System assemblies. Works with INCRA's new Build-It T-Slot Panel Connector and all INCRA T-Track (and other brands that use 1/4"-20 hardware). Includes (2) brackets, (4) knobs, (4) bolts and (4) washers. Made in USA.
|
|
|
|
|
NEW!
SAVE 22% ON MICROJIG MAGNETIC DUST COVERS
Now only $8.45
MicroJig’s Magnetic Dust Cover closes the bevel slot on steel left-tilt cabinet saws, focusing dust collection airflow where it’s most effective. Trim to fit with scissors, removes instantly, and can be reversed when cutting bevels.
|
|
|
SAVE 21% ON INCRA GAUGES
Now only $14.95
This handy accessory brings INCRA accuracy and repeatability to a wide range of setup and layout jobs around your shop. INCRA's patented incremental racks are molded into each half of the gauge, causing settings to automatically snap to the dead center of the nearest 1/32", plus or minus only a few thousandths of an inch. Works great for setting router bit or saw blade heights, laying out mortise & tenon joints, making fence setups on saws & router tables, and much more. Made in USA.
|
|
|
|
|
|
