Click here to watch the TS-LS Demo - Part 1 of 3
Click here to watch the TS-LS Demo - Part 2 of 3
Click here to watch the TS-LS Demo - Part 3 of 3
Click here to watch the TS-LS Table Saw Fence Video (from New Woodworker)

For 30 years, INCRA Saw Fences have been the Gold Standard for Accuracy, Repeatability, and Efficiency.

Whether you paid $500 or $4,500 for your table saw, accurate work starts with a better rip fence.

A TS-LS system has one big advantage over your current rip fence: INCRA fences measure their distance from the blade mechanically, so your cutting accuracy doesn’t depend on your skill level, how good your shop lighting is, or how fresh your eyes are.


Advanced design:

Simple, patented lead screw-based mechanics instantly position the fence in 1/32” steps +/-0.002” (1mm +/- 0.05mm for metric versions) with perfect repeatability… you can’t miss!

Integrated micro adjust knob allows moving between 1/32” steps in 0.001” resolution

Fence locks at 3 points for exceptional stiffness

52” or 1320mm right-side ripping capacity, 92" main rail with (find the 32”-capacity TS-LS here)

32" travel INCRA LS Positioner

Fence locks at 3 points for exceptional stiffness

Consistent alignment relative to the blade

Fence T-slots accommodate hold downs and wooden sub fences

Adjustable brackets for straightforward installation on a huge variety of table saws (see Compatibility below)

Expandable in the future with routing accessories


Spend less time tapping and measuring!
It’s fast – each time you pull the red locking lever, the lead screw mechanism instantly snaps the fence to the center of the nearest 1/32" or 1 mm increment with an accuracy of +/- 0.002", that’s accurate enough to split a sharp pencil line into a dozen equal parts. No guesswork, no fine-tuning needed.

The lead screw mechanics let you quickly repeat any fence position hours or days later so you can use your saw in new ways – make repetitive cuts with ease, turn out complex project parts that require several different fence settings, and more.



The TS-LS is already perfect on increments of 1/32” or 1mm, but when you need to match existing project parts, the large micro-adjust knob moves the fence between the 1/32” steps with 0.001" (0.025mm) resolution.






Straightforward installation, flexible configuration:
Adjustable brackets make the TS-LS System a nuts-and-bolts installation on a wide variety of table saws, and the owner’s manual is excellent.



Quick-release knobs let the base assembly slide anywhere left-right along the main rails to access a router table, and the whole system lifts off the rails in seconds. 3 sets of stops on the rails maintain perfect alignment & calibration each time it’s moved.






Compatibility:

Choose Standard or XL:
The standard TS-LS covers saws measuring 28" or smaller front-to-rear along the miter slot. The XL version uses a longer fence and base support panel to fit saws with deeper tables measuring 33.5” or less.

The saw’s left-to-right width isn’t important for systems not equipped with router tables. You’ll keep your cast iron wings installed, and your existing extension tables can be reused.

Compatibility requirements for ALL table saws:
• The saw’s top must have flat, vertical surfaces on both the front and rear for the (4) adjustable Incra rail mounting brackets to bolt against – two brackets at the front and two on the rear.
• The brackets are attached with a minimum 5/16”-18 or 8mm bolt. Note: Some metric table saws will require additional common bolts for rail installation due to a lack of standardization.
• The bolt holes need to be centered between 3/4” and 1-3/8” down from the saw’s top surface, with enough clearance underneath the saw’s top for washers, nuts and wrench (if the holes aren’t threaded).




The General Compatibility Chart lists the various categories of saws, and the TS-LS owner's manual is the best resource for seeing how the 4 rail mounting brackets attach for comparison with your saw.




Made in USA.